|
6. ENGINEERING - MECHANICAL |
|
|
JS 25: 2010 |
Transportable gas containers This standard specifies requirements for the materials, design, construction and testing of containers for the conveyance of permanent, liquefiable and dissolved gases under pressure. Such containers are suitable also for storing gas under pressure. It applies to steel containers of water capacity 0.5 L up to 150 L(150 kg) having longitudinal and/ or circumferential main seams, made by a fully or semi- automatic welding process. Mandatory. ISBN 976-604-486-2 |
|
|
JS 28: 1973 |
Commercial butane and commercial propane-butane mixtures Specifies the properties of butane and propane-butane mixtures used for domestic, commercial and industrial purposes in Jamaica. |
|
|
JS 30: 1974 (2017) |
Manhole step irons Details requirements for the design, workmanship, finish and mechanical properties of manhole step irons for general purposes and for use in circular and across corners of rectangular pre-cast concrete manholes and inspection chambers. Mandatory. |
|
|
JS 31: 2014 |
The repair and rebuilding of low – pressure welded steel transportable gas containers Specifies the requirements for the repair and rebuilding of low-pressure transportable gas containers made in accordance with JS 25 Jamaican Standard Specification for Transportable gas containers, and the subsequent testing of these transportable gas containers before re-use. This standard does not apply to containers designed and manufactured to contain dissolved acetylene. Repairs to valves and fittings, which are not permanent attachments to the transportable gas container, shall not be covered by this standard. Mandatory. ISBN 978-976-604-623-1. |
|
|
JS 41: 2014
|
Inspection, retesting and use of transportable gas containers Specifies requirements for inspection, retesting and use of steel cylinders manufactured in accordance with JS25 or any other applicable Code of Federal Regulations Standard Title 49. It also applies as far as practicable to cylinders of less than 1L capacity. It does not apply to cylinders containing dissolved acetylene. Mandatory ISBN 978-976-604-596-8
|
|
|
JS 42: 1975 (1984) (2017) |
The manufacture of steel wire rope slings Applies to the construction, inspection, acceptance testing, marking and certification of steel wire rope slings (Confirmed 1984). Mandatory |
|
|
JS 43: 1975 (1984) |
The use and maintenance of steel wire rope slings Recommends good practices in the use and maintenance of wire rope slings. |
|
|
JS 76: 1980 (2017) |
The construction of portable metal ladders Stipulates rules and minimum requirements for the design, construction and performance of the common types of portable metal ladders used in the industrial, commercial and domestic sectors. It does not cover special-purpose ladders which do not meet the general requirements of this standard. Mandatory. |
|
|
JS 77: 1980 |
The care and use of portable metal ladders Provides basic user guidance for the safe and proper care of metal ladders and outlines how maximum serviceability can be achieved. Read in conjunction with JS 76 |
|
|
JS 134: 1985 |
Refrigerators burning liquid petroleum gas Specifies detailed requirements, including performance standards and methods of test, for gas-operated refrigerators for temporary storage of food in tropical climates. ISBN 976-604-044-3 |
|
|
JS 244 : 2006 |
Pneumatic tyres for passenger cars This standard specifies tyre dimensions and laboratory test requirements for bead unseating resistance, strength, endurance and high speed performance ; defines tyre load ratings and other relevant terms; and specifies labelling requirements for passenger car tyres. ISBN 976604-443-0
|
|
|
JS 262: 1992 |
Motor vehicle brake fluid Specifies requirements for fluids for use in hydraulic brake systems of motor vehicles, containers for these fluids and labelling of the containers. Mandatory. ISBN 976-604-285-3 |
|
|
JS 267: 1999 |
Electronic taximeters Details characteristics, methods of calculation and tests, programming, marking, design and constructional requirements for taximeters to be installed in public hire vehicles (hackney carriages or taxis). Does not apply to taximeters that are remotely controlled. Mandatory. ISBN 976-604-294-2 |
|
|
JS 269 : 2006 |
Pneumatic tyres for vehicles other than passenger cars This standard establishes performance and marking requirements for tyres for use on multipurpose passenger vehicles, trucks buses, trailers and motorcycles. ISBN 976-604-442-2 |
|
|
JS 277: 2014 |
Household cooking gas appliances Applies to household cooking gas appliances (see Section three, Definitions), hereinafter referred to as units or appliances, constructed entirely of new, unused parts and materials. These appliances may be floor supported or built-in. 1.1.2 This standard applies to household cooking appliances for use with: (a) natural gas (b) manufactured gas (c) mixed gas (d) liquefied petroleum gases (e) LP gas-air mixtures (f) either natural, manufactured or mixed gas and convertible for use with liquefied petroleum gases Mandatory. ISBN 978-976-604-577-7 |
|
|
JS 322 : 2012 |
Transportable gas cylinders – Fully wrapped composite cylinders Specifies minimum requirements for the materials, design, construction, prototype testing and routine manufacturing inspections of composite gas cylinders with a water capacity up to and including 450 l for compressed, liquefied and dissolved gases. NOTE. For the purposes of this standard, the word ―cylinder‖ includes tubes up to 450 l water capacity This standard is applicable to cylinders that comprise a liner of metallic material (welded or seamless) or non-metallic material (or a mixture thereof), reinforced by a wound composite consisting of fibres of glass, carbon or aramid (or a mixture thereof) embedded in a matrix. This standard is also applicable to composite cylinders without liners. This standard is not applicable to gas cylinders which are partially covered with fibres and commonly called "hoop wrapped" cylinders. For hoop wrapped composite cylinders see EN 12257. NOTE. The specification does not ad dress the design, fitting and performance of re movable protective sleeves. Where these are fitted they should be considered separately. Mandatory. ISBN 978- 976-604-510-4 |
|
|
JS 323 : 2012 |
Transportable gas cylinders – Periodic inspection and testing of composite gas cylinders Specifies the requirements for periodic inspection and testing of hoop wrapped and fully wrapped composite transportable gas cylinders, with aluminum, steel or non-metallic liners or of linerless construction, intended for compressed, liquefied or dissolved gases under pressure, of water capacity from 0.5 l up to 450 l. NOTE. As far as practicable, this standard may also be applied to cylinders of less than 0.5 l water capacity. This standard specifies the requirements for periodic inspection and testing to verify the integrity of such gas cylinders for further service. Mandatory. ISBN 978-976-604-511-1 |
|
|
JS 239: 1994 |
Domestic cooking appliances using keroseneISBN 976-604- 223-3 |
|
|
JS CRS 17 : 2010 (2017) |
Gold articles Specifies: a) requirements for the manufacturing, alloying and testing of gold articles of 23, 22, 20, 18, 15, 14,12, 10 and 9 kt gold; b) requirements for findings and solders to be used in the manufacture of gold articles; c) methods for assaying gold, alloyed gold, solder, findings and gold articles; and d) requirements for marking and labelling of imported gold articles. NOTE: It does not specify requirements for design of gold articles and does not apply to gold articles intended for industrial purposes such as dentistry, electronics, official coins, gold bars and other such uses. ISBN 978-976-604-512-8
|
JS ISO 11711-1: 2016 |
Jamaican Standard Specification for Piping and machinery — Ballast water sampling and analysis — Part 1: Discharge sampling port This part of ISO 11711 provides guidance to shipboard personnel and other concerned parties on the materials, design, and installation of equipment used to take samples of treated ballast water from the ballast water discharge pipe onboard a vessel. The purpose of the sampling system is to enable the taking of a representative sample in order to verify that the ballast water management system (BWMS) is working as designed, i.e. the treatment is reducing the concentration of living organisms to levels established in discharge standards. The intent of the sampling installation is to provide a representative sample of the blast water effluent with adequate pressure and flow. ISBN 978-976-604-692-7 |
|
|
JS ISO 3779 : 2009 |
Road vehicles —Vehicle Identification Number (VIN) — Content and structure Specifies the content and structure of a vehicle identification number (VIN) in order to establish, on a world-wide basis, a uniform identification numbering system for road vehicles. ISBN 978-976-604-521-0 |
|
|
JS JIS D 4901: 1982 |
Vehicle identification numberSpecifies the indicating symbol and number of identification number and indicating method thereof to be indicated on the road vehicles. ISBN 976-604-434-1 |
Please share your feedback below and help us improve our content.